Caravan Hot Water Systems: Gas, Electric and Off-Grid Power Options
A caravan hot water system should suit your shower demand, the fuel you can carry and the electrical supply you have. Gas works well for unpowered stays, electric heating suits powered sites, and dual-fuel systems let you pick between the two. Before you replace a unit or add battery power, find out how it heats the water, what its controls need and whether your existing installation is compatible.
Key Takeaways
A 12V connection may power the controls without heating the water electrically.
Compare usable mixed water and reheating time as well as tank capacity.
Continuous-flow systems still need suitable water flow, fuel and electricity.
Electric heating needs enough output and enough stored energy.
Plan any replacement plumbing, gas and electrical work with appropriately licensed tradespeople.
How Do Gas, Electric and Dual-Fuel Caravan Hot Water Systems Differ?
The main difference is which energy source heats the water. Electrical requirements also cover controls, ignition and pumps, and these can still be needed when gas supplies the heat.
System Type | Water Heating Source | Electrical Supply Required | Storage or Continuous Flow | Main Installation Requirement | Main Limitation |
Gas | LPG burner | Often 12V controls and ignition | Both available | Approved gas supply and flue | Fuel and flow requirements |
Electric storage | Heating element | Rated AC supply | Storage | Suitable circuit and plumbing | Heating load and recovery |
Dual-fuel | Gas or electric element | Model-specific DC and AC | Commonly storage | Both supplies installed correctly | More installation requirements |
True 12V electric | DC heating element | Dedicated compatible DC supply | Commonly small storage | Rated wiring and protection | Current demand and heating time |
Gas Systems and Their Electrical Control Requirements
Gas supplies the heat, but many caravan units still need 12V electricity for ignition, valves and electronics. The water pump may need power too. A full gas bottle won’t help if the control battery is flat. Read the model’s supply requirements and include these smaller loads when you plan an off-grid caravan power system.
Electric Storage Systems for Powered Sites
An electric storage system heats a tank with an element and thermostat. At a powered site, check the element’s input against the other appliances sharing the supply. Hot water is available only within the tank’s usable reserve and its recovery capability. Make sure the tank is filled and purged as instructed before you energise an element that has to stay submerged.
Dual-Fuel Systems for Switching Between Gas and Electricity
Dual-fuel caravan hot water systems give you both gas and electric heating. Electricity can save LPG at powered stops, while gas can reduce battery demand away from mains. Check which controls select each mode and whether both can run at once. Both supplies must be installed correctly, and switching modes doesn’t remove the maintenance requirements of either installation.
Is a 12V Hot Water System Practical for a Caravan?
Yes, a genuine 12V hot water system can suit modest demand when the battery and wiring support it. The Duoetto MK2, for example, specifies 300W and 25A in its 12V heating mode. That requires a dedicated, correctly designed and protected circuit; it cannot be supplied through a 10A vehicle socket or a power station’s 10A car-style outlet. Its higher-powered AC mode has different supply requirements. Check the exact model and budget the full heating session.
How Much Hot Water Does Your Caravan Need?
Work out shower use first, then compare the heater’s usable supply and recovery. Include washing-up water and the fresh-water and greywater capacity you have between stops.
Shower Duration, Flow Rate and Number of Users
Multiply the shower flow by the time the water runs and by the number of users. At an assumed 4L/min for three minutes each, two people use 24L of mixed water. Turning the flow off while you soap up cuts consumption. Measure your own showerhead with a container and a timer, since pump settings and restrictions change the result.
Tank Capacity and Usable Mixed-Water Volume
Stored hot water gets mixed with cold, so tank size isn’t the same as shower volume. Ideally, 10L stored at 60°C mixed with 20°C cold water gives 20L at 40°C. Actual delivery is affected by heat loss, mixing and the temperature of the incoming cold water. Treat this as an illustrative calculation, and keep to the manufacturer’s required temperature settings.
Recovery Time Between Showers
Recovery depends on the heating mode and the temperature rise required. As a specific reference, the Truma UltraRapid lists approximately 45 minutes on gas, 40 minutes on electricity and 28 minutes in mixed mode to heat 14L from about 20°C to 65°C. Compare equivalent conditions, and stagger showers if the stored supply can’t cover everyone.
Continuous-Flow Performance, Water Pressure and Temperature Rise
Continuous flow avoids waiting for a whole tank to reheat, but its heating capacity is still finite. Colder incoming water needs more heat to reach the same outlet temperature, which can limit delivery. Check the minimum activation flow, the permitted pressure and the rated temperature-rise performance. A showerhead that restricts flow too far can cause cycling or a failure to ignite.


What Should You Check Before Replacing a Caravan Hot Water System?
Match the complete installation, including access, supply connections and safe discharge routes. A replacement of similar capacity may still need different cabinetry, wiring or flue arrangements.
Cabinet Space, Service Access and Installed Weight
Measure the enclosure and the exterior opening against the installation drawing. Leave access to the controls, connections, drains and service parts. Include the water in the installed weight: a nominal 14L fill adds approximately 14kg to the appliance’s dry weight. Check the mounting support and the caravan’s payload before you choose a larger tank.
Water Connections, Pump Pressure and Relief Valve Drainage
Compare inlet and outlet positions, fitting sizes and pressure limits with the existing plumbing. Check both the pump and any mains-water connection. The relief valve’s discharge needs the specified unobstructed route to a safe location. Ask the installer whether pressure regulation or other changes are required, and never cap a dripping relief outlet.
Gas Supply, Flue Position and Ventilation
The gas type, regulator arrangement, flue location and ventilation must all suit the approved installation. An annexe can change where the exhaust discharges. Queensland’s caravan gas safety guidance specifically addresses flue discharge outside annexes or attached enclosures. Ask the gasfitter to assess your planned awning arrangement alongside the heater location.
Electrical Connections and Circuit Capacity
Identify the separate AC element and DC control connections. Check the heater’s rated input, the circuit protection and the other equipment sharing the supply. A plug that physically matches doesn’t make the connection electrically suitable. Have a licensed electrician assess the fixed wiring, earthing and RCD protection, including any proposed change from mains to inverter power.
Licensed Installation and Compatibility with Existing Plumbing
Use appropriately licensed tradespeople for the gas, electrical and regulated plumbing work involved. Give them the old and proposed model numbers before you buy. Ask them to confirm connection compatibility, required alterations and commissioning checks, together with the applicable compliance documentation. An installation quote can reveal costs that make repairing the existing unit worth considering.
How Can You Keep Hot Water Available When Camping Off-Grid?
Choose heating around the LPG you have, the electricity you’ve stored and the recharging you can realistically count on. Shorter showers and planned reheating can reduce the resources you need without changing the installed heater.
Choosing Gas or Electric Heating Around Available Fuel and Power
Gas can save battery energy when sunshine is limited or refrigeration takes priority. Electric heating can draw on available battery reserves or mains power at a stop. With a dual-fuel unit, plan which source will cover each day. Keep enough electricity for the controls and pumps even if you intend to heat with gas alone.
Heating Energy per Tank and Daily Hot-Water Use
For water alone, energy in Wh is approximately litres × temperature rise in °C × 1.163. Heating an assumed 10L from 20°C to 60°C needs about 465Wh before tank heating and losses; two complete reheats need approximately 930Wh on the same ideal basis. Use measured heating-session consumption when sizing a portable power station, then add conversion losses, other loads and reserve. Check output separately against the heating element’s electrical input.
Using a Portable Power Station with a Compatible Plug-In Water Heater
For a heater operating in a compatible AC mode through an approved plug-in connection, the EcoFlow DELTA 3 Max Plus offers 3,000W of rated total AC output and 2,048Wh of nominal capacity. Check the element and simultaneous loads, then budget actual reheating energy. This AC output does not establish compatibility with a heater’s separate 12V mode; its voltage, current and connection require their own assessment. Compatible solar and optional alternator charging provide replenishment options. Fixed-wired heaters need an electrician-assessed connection, and Smart Output Priority must be configured so planned heating is not unexpectedly interrupted.
More Battery Capacity for Repeated Heating Between Recharges
For several users and repeated reheating, the EcoFlow DELTA Pro 3 provides 4,096Wh of nominal storage and 4,000W of rated AC output. Twice the nominal capacity of the DELTA 3 Max Plus gives you more energy between recharges, and the extra output helps with compatible simultaneous loads. Expansion with compatible extra batteries supports larger budgets, while up to 2,600W of solar input offers recharging potential with a suitable array. Weigh these advantages against your actual daily heating demand and what you can carry. More storage won’t turn a small tank into a continuous electric shower, and it doesn’t guarantee enough energy for every appliance.
Scheduling Reheating Around Solar Input and Powered Stops
Heat the water ahead of planned showers, when the tank can hold that warmth, and use powered stops for electric reheating where it’s permitted. With solar, schedule heating around the energy actually coming in and your battery reserves. A suitable camping solar setup has to account for shade, weather and other loads. Keep a fallback, such as an approved gas mode, for days when recharging is poor.
Conclusion
Choose a caravan hot water system around usable shower water, recovery time and the supplies your trips provide. Check installation compatibility before replacing equipment, then budget the heating energy alongside the fridge, lights and pumps. Suitable battery power can support planned electric reheating, while gas and powered stops offer alternatives when you need to conserve stored energy.
Caravan Hot Water System Questions
Why Does My Caravan Hot Water Work on Gas but Not Electricity?
The AC supply, element switch, protective device or element itself may be at fault. Check the accessible controls and supply indicators using the manual. If protection trips or heating still fails, switch off the electric mode and arrange a qualified service.
Can You Run Gas and Electric Heating at the Same Time?
Yes, if the model explicitly supports mixed operation. It can shorten recovery time, but both supplies must be available and correctly installed. Follow the operating instructions, because separate gas and electric switches don’t automatically mean it’s permitted.
Why Is Water Dripping from the Pressure Relief Valve?
Small amounts during heating can come from thermal expansion. Continuous or substantial discharge needs assessing for pressure, temperature or valve problems. Keep clear of the hot water and never plug the outlet. Arrange a service if the discharge is abnormal.
Should You Drain the Hot Water Tank Before Storing Your Caravan?
Drain it when the manufacturer’s storage or frost instructions require it. Switch off all heating sources, let the unit cool and release the pressure as directed. Refill and purge the system before reheating, and never energise an empty storage heater.
How Do You Check Whether Your Hot Water System Needs a Sacrificial Anode?
Find the exact model in the maintenance manual and look for an anode inspection schedule. Some enamel-lined tanks use replaceable anodes, while other designs don’t. Use the specified replacement and service interval, and avoid opening a hot, pressurised tank.